进口塑胶料
注:请在右边的搜索栏查找产品

PBT 3316 含30%玻纤增强,阻燃

添加时间:2013-05-26  信息来源:http://www.simibc.com/  作者:苏州希普能塑料
泰科纳PBT 3316
 
CELANEX® 3316 EA4344 WHITE
CELANEX® 3316 EA4623U WHITE
CELANEX® 3316 EC3580 GRAY
CELANEX® 3316 EC4174 GRAY
CELANEX® 3316 EC4337 GRAY
CELANEX® 3316 EC4447 GRAY 7035
CELANEX® 3316 EC4587 GRAY
CELANEX® 3316 ED3002 BLACK
CELANEX® 3316 EF3022 NATURAL
CELANEX® 3316 EG4014 BLUE
CELANEX® 3316 EG4071 BLUE
CELANEX® 3316 EG4163 BLUE
CELANEX® 3316 EG4443 BLUE
CELANEX® 3316 EJ4138 GREEN
CELANEX® 3316 EL4111 YELLOW
CELANEX® 3316 ES4511 RED
CELANEX® 4305 EF3022 NATURAL
 
CELANEX 3316 | PBT | Glass Reinforced
 
UL黄卡
E45575-239391
E45575-239392
E42337-234679
E42337-234663
E42337-234678
 
Description
Celanex 3316 is a non-exuding flame retarded (UL and CSA approved V-0 at 1/32 inch and 5V at 1/16 inch), 30% fiberglass reinforced polybutylene terephthalate which has an excellent balance of mechanical properties and processability. It is well suited for electrical connector applications where its UL approved 50% regrind use capability allows maximum use of purchased product.
 
Other Processing
Injection Molding
Rear Temperature    450-470(230-240) deg F (deg C)
Center Temperature  460-480(235-250) deg F (deg C)
Front Temperature   470-490(240-255) deg F (deg C)
Nozzle Temperature  480-490(250-255) deg F (deg C)
Melt Temperature    460-490(235-255) deg F (deg C)
Mold Temperature    150-200(65-93)   deg F (deg C)
Back Pressure       0-50             psi
Screw Speed         Medium
Injection Speed     Fast
 
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the '16 series' flame retardant grades.
 
ISO Data Physical properties Value Unit Test Standard
Phys Density 1660 kg/m³ ISO 1183
Melt volume rate (MVR) 7 cm³/10min ISO 1133
MVR test temperature 250 ISO 1133
MVR test load 2.16 kg ISO 1133
Mold shrinkage - parallel 0.1 to 0.8 % ISO 294-4
Mold shrinkage - normal 0.8 to 1.3 % ISO 294-4
Humidity absorption (23℃/50%RH) 0.16 % ISO 62
Mech Mechanical properties Value Unit Test Standard
Tensile modulus (1mm/min) 10700 MPa ISO 527-2/1A
Tensile stress at break (5mm/min) 135 MPa ISO 527-2/1A
Tensile strain at break (5mm/min) 2.5 % ISO 527-2/1A
Flexural modulus (23℃) 10300 MPa ISO 178
Flexural strength (23℃) 200 MPa ISO 178
Charpy impact strength @ 23℃ 59 kJ/m² ISO 179/1eU
Charpy impact strength @ -30℃ 42 kJ/m² ISO 179/1eU
Charpy notched impact strength @ 23℃ 8.5 kJ/m² ISO 179/1eA
Charpy notched impact strength @ -30℃ 8.5 kJ/m² ISO 179/1eA
Notched impact strength (Izod) @ 23℃ 7.7 kJ/m² ISO 180/1A
Rockwell hardness 89 M-Scale ISO 2039-2
Therm Thermal properties Value Unit Test Standard
Melting temperature (10℃/min) 225 ISO 11357-1,-2,-3
DTUL @ 1.8 MPa 208 ISO 75-1/-2
DTUL @ 0.45 MPa 220 ISO 75-1/-2
DTUL @ 8.0 MPa 165 ISO 75-1/-2
Vicat softening temperature B50 (50℃/h 50N) 225 ISO 306
Coeff.of linear therm. expansion (parallel) 0.25 E-4/℃ ISO 11359-2
Coeff.of linear therm. expansion (normal) 0.77 E-4/℃ ISO 11359-2
Limiting oxygen index (LOI) 30 % ISO 4589
Flammability at thickness h V-0 class UL94
thickness tested (h) 0.38 mm UL94
Flammability 5V at thickness h 5VA class UL94
thickness tested (5V) 1.5 mm UL94
Elec Electrical properties Value Unit Test Standard
Relative permittivity - 100 Hz 3.6 - IEC 60250
Relative permittivity - 1 MHz 2.9 - IEC 60250
Dissipation factor - 100 Hz 33 E-4 IEC 60250
Dissipation factor - 1 MHz 145 E-4 IEC 60250
Volume resistivity 1E13 Ohm*m IEC 60093
Surface resistivity 1E15 Ohm IEC 60093
Electric strength 34 kV/mm IEC 60243-1
Comparative tracking index CTI 250 - IEC 60112
SpecProd Test specimen production Value Unit Test Standard
Processing conditions acc. ISO 7792-2 - Internal
Injection molding melt temperature 260 ISO 294
Injection molding mold temperature 82 ISO 294
Injection molding flow front velocity 300 mm/s ISO 294
Injection molding hold pressure 48 MPa ISO 294
 
Processing
Pre Drying
Necessary low maximum residual moisture content: 0.02%
 
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40℉ (-40℃) at 250℉ (121℃) for 4 hours.
 
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100℃.
 
Drying time (h):4
Drying temperature (℃):120 - 130
希普能工程塑料
相关材料