进口塑胶料
注:请在右边的搜索栏查找产品

LNP STAT-KON PBT WS002I

添加时间:2013-02-22  信息来源:http://www.simibc.com/  作者:苏州希普能塑料
LNP™ STAT-KON™ Compound PBT WS002I
 
Also known as:LNP™ Stat-kon™ Compound WS-HI Product reorder name:WS002I
LNP* Stat-kon* WS002I is a compound based on Polybutylene Terephalate resin containing Stainless Steel. Added features of this material include: Electrically Conductive, High Impact.
 
Property
TYPICAL PROPERTIES(1)
MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,5mm/min 390 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5mm/min 350 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5mm/min 4 % ASTM D 638
Tensile Strain,brk,Type I,5mm/min 15.8 % ASTM D 638
Tensile Modulus,50mm/min 23100 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span 640 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 20600 kgf/cm² ASTM D 790
Tensile Stress,yield,5mm/min 37 MPa ISO 527
Tensile Stress,break,5mm/min 34 MPa ISO 527
Tensile Strain,yield,5mm/min 4.1 % ISO 527
Tensile Strain,break,5mm/min 16.5 % ISO 527
Tensile Modulus,1mm/min 2140 MPa ISO 527
Flexural Stress 67 MPa ISO 178
Flexural Modulus,2mm/min 1920 MPa ISO 178
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 102 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 7 cm-kgf/cm ASTM D 256
Multiaxial Impact 80 cm-kgf ISO 6603
Instrumented Impact Total Energy,23℃ 63 cm-kgf ASTM D 3763
Izod Impact,unnotched 80*10*4 +23℃ 69 kJ/m² ISO 180/1U
Izod Impact,notched 80*10*4 +23℃ 7 kJ/m² ISO 180/1A
THERMAL Value Unit Standard
HDT,0.45 MPa,3.2mm,unannealed 173 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 59 ASTM D 648
CTE,-30℃ to 30℃,flow 9.50E-05 1/℃ ASTM D 696
CTE,-30℃ to 30℃,xflow 1.05E-04 1/℃ ASTM D 696
HDT/Bf,0.45 MPa Flatw 80*10*4 sp=64mm 115 ISO 75/Bf
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 58 ISO 75/Af
PHYSICAL Value Unit Standard
Density 1.3 g/cm³ ASTM D 792
Moisture Absorption,50% RH,24 hrs 0.09 % ASTM D 570
Mold Shrinkage,flow,24 hrs(5) 1-3 % ASTM D 955
Mold Shrinkage,xflow,24 hrs(5) 1-3 % ASTM D 955
Density 1.31 g/cm³ ISO 1183
Moisture Absorption(23℃/50% RH) 0.13 % ISO 62
ELECTRICAL Value Unit Standard
Surface Resistivity 2.E+00-4.E+00 Ohm ASTM D 257
Source GMD,last updated:2009/08/27

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.

PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

相关材料
上一页:PBT W3000XXJ compound 抗静电,医疗级           下一页:LNP STAT-KON PBT WEF42I