进口塑胶料
注:请在右边的搜索栏查找产品

PA66 12T NC010 含36%矿物,增韧,热稳定

添加时间:2013-11-16  信息来源:http://www.simibc.com/  作者:苏州希普能塑料

Minlon PA66 12T NC010

Minlon® 12T NC010 | PA66-I-MD36 MINERAL REINFORCED NYLON RESIN
 
Regional Availability
North America, South and Central America
 
Processing
Injection Moulding
 
Delivery form
Pellets
 
Special characteristics
Heat stabilised or stable to heat
 
Product Text
Common features of Minlon® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness /toughness, good high temperature performance, good chemical resistance, paintability, dimensional stability and low warpage.
 
Grades with improved electrical and flammability properties are available within the Zytel® nylon resin product line. In addition, Minlon® nylon resin is available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses.
 
The good melt stability of Minlon® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Minlon® nylon resin typically is used in demanding applications in the automotive, electrical, electronic, domestic appliances and construction industries.
 
Minlon® 12T NC010 is a 36% mineral reinforced, toughened, heat stabilised, black polyamide 66 resin for injection moulding.
 
Injection molding
PREPROCESSING
Drying recommended = Yes
Drying temperature = 80℃
Drying time, dehumidified dryer = 2-4h
Processing moisture content = <0.2%
 
PROCESSING
Melt temperature optimum = 295℃
Melt temperature range = 285-305℃
Mould temperature optimum = 100℃
Mould temperature range = 70-120℃
 
PROPERTIES
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage,parallel 0.9 / * % ISO 294-4,2577
Moulding shrinkage,normal 0.9 / * % ISO 294-4,2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 4900 / 2000 MPa ISO 527-1/-2
Stress at break 80 / 58 MPa ISO 527-1/-2
Strain at break 18 / 40 % ISO 527-1/-2
Charpy impact strength,23℃ 210 / 330 kJ/m² ISO 179/1eU
Charpy impact strength,-30℃ 90 / 120 kJ/m² ISO 179/1eU
Charpy notched impact strength,23℃ 9 / 15 kJ/m² ISO 179/1eA
Charpy notched impact strength,-30℃ 5 / 4 kJ/m² ISO 179/1eA
Charpy notched impact strength,-40℃ 4 / 3 kJ/m² ISO 179/1eA
Thermal properties dry / cond Unit Test Standard
Melting temperature,10℃/min 256 / * ISO 11357-1/-3
Temp. of deflection under load,1.8 MPa 80 / * ISO 75-1/-2
Temp. of deflection under load,0.45 MPa 205 / * ISO 75-1/-2
Coeff. of linear therm. expansion,parallel 64 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion,normal 65 / * E-6/K ISO 11359-1/-2
Flammability dry / cond Unit Test Standard
Burning Behav. at thickness h HB / * class IEC 60695-11-10
Thickness tested 0.8 / * mm IEC 60695-11-10
Oxygen index 25 / * % ISO 4589-1/-2
Electrical properties dry / cond Unit Test Standard
Relative permittivity,100Hz 4 / - - IEC 60250
Relative permittivity,1MHz 3.8 / - - IEC 60250
Dissipation factor,100Hz 100 / - E-4 IEC 60250
Dissipation factor,1MHz 100 / - E-4 IEC 60250
Volume resistivity 1E11 / - Ohm*m IEC 60093
Electric strength 24 / - kV/mm IEC 60243-1
Comparative tracking index 400 / - - IEC 60112
Other properties dry / cond Unit Test Standard
Water absorption,2mm 6.2 / * % Sim. to ISO 62
Humidity absorption,2mm 1.7 / * % Sim. to ISO 62
Density 1410 / - kg/m³ ISO 1183

 

Chemical Media Resistance
Alcohols
√ Ethanol (23℃)
Hydrocarbons
√ Toluene (23℃)
√ iso-Octane (23℃)
Standard Fuels
√ ISO 1817 Liquid 3 (60℃)

 

Symbols used:
√ possibly resistant
Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

 

× not recommended - see explanation
Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).

联系湘樟塑料

相关材料