进口塑胶料
注:请在右边的搜索栏查找产品

LNP STAT-KON PA66 REF42I

添加时间:2013-02-21  信息来源:http://www.simibc.com/  作者:苏州希普能塑料

LNP™ STAT-KON™ Compound PA66 REF42I

 

Also known as:LNP™ Stat-kon™ Compound PDX-R-86624 Product reorder name:REF42I
LNP* Stat-Kon* REF42I is a compound based on Nylon 6/6 containing Proprietary Fillers. Characteristics of this grade are Electrically Conductive.

 

Property
TYPICAL PROPERTIES(1)

MECHANICAL Value Unit Standard
Tensile Stress,brk,Type I,5mm/min 2000 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,5mm/min 2.6 % ASTM D 638
Tensile Modulus,50mm/min 149400 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span 2820 kgf/cm² ASTM D 790
Flexural Stress,brk,1.3mm/min,50mm span 2790 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 117200 kgf/cm² ASTM D 790
Tensile Stress,yield,5mm/min 195 MPa ISO 527
Tensile Stress,break,5mm/min 176 MPa ISO 527
Tensile Strain,yield,5mm/min 2.6 % ISO 527
Tensile Strain,break,5mm/min 2.7 % ISO 527
Tensile Modulus,1mm/min 13870 MPa ISO 527
Flexural Stress 264 MPa ISO 178
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 101 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 14 cm-kgf/cm ASTM D 256
Multiaxial Impact 45 cm-kgf ISO 6603
Instrumented Impact Total Energy,23℃ 230 cm-kgf ASTM D 3763
Izod Impact,unnotched 80*10*4 +23℃ 62 kJ/m² ISO 180/1U
Izod Impact,notched 80*10*4 +23℃ 12 kJ/m² ISO 180/1A
THERMAL Value Unit Standard
HDT,0.45 MPa,3.2mm,unannealed 261 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 253 ASTM D 648
CTE,-30℃ to 30℃,flow 1.60E-05 1/℃ ASTM D 696
CTE,-30℃ to 30℃,xflow 9.40E-05 1/℃ ASTM D 696
HDT/Bf,0.45 MPa Flatw 80*10*4 sp=64mm 260 ISO 75/Bf
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 247 ISO 75/Af
PHYSICAL Value Unit Standard
Specific Gravity 1.3 - ASTM D 792
Density 1.3 g/cm³ ASTM D 792
Moisture Absorption,50% RH,24 hrs 0.69 % ASTM D 570
Mold Shrinkage,flow,24 hrs(5) 0.2-0.4 % ASTM D 955
Mold Shrinkage,xflow,24 hrs(5) 0.8-1 % ASTM D 955
Moisture Absorption(23℃/50% RH) 0.96 % ISO 62
ELECTRICAL Value Unit Standard
Surface Resistivity 1.E+00-4.E+00 Ohm ASTM D 257
Source GMD,last updated:2009/08/11
Parameter Injection Molding Value Unit
Drying Temperature 80
Drying Time 4 hrs
Maximum Moisture Content 0.15-0.25 %
Melt Temperature 280-305
Front-Zone 3 Temperature 295-305
Middle-Zone 2 Temperature 280-295
Rear-Zone 1 Temperature 265-275
Mold Temperature 95-110
Back Pressure 0.2-0.3 MPa
Screw Speed 30-60 rpm
Source GMD,last updated:2009/08/11

相关材料
上一页:LNP STAT-KON PA66 REL42           下一页:LNP STAT-KON PA66 REF42